View TA1201CNG_4378634.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TA1201CNG 2004-05-24 1 toshiba bipolar linear integrated circuit silicon monolithic TA1201CNG i 2 c bus control ntsc 1chip color tv ic TA1201CNG provides pif, sif, video, chroma and deflection circuit for ntsc color tv. TA1201CNG also provides audio-video switch and text interface. TA1201CNG combine these functions in a 56pin dual-in-line shrink-type plastic package. TA1201CNG realizes rationalization of various alignments and controls by bus control system. features pif circuit ? pll type if demodulation (bus alignment) ? adjustment free aft without tank coil ? rf agc output (delay point : bus alignment) ? dual time constant fast agc video circuit ? black stretcher ? dc restoration circuit ? d.l. aperture compensate circuit (bus control) ? internal filter auto-adjust circuit (fsc link type) ? uni-color circuit (bus control) ? 3.58mhz trap filter circuit (bus on / off) ? y delay line circuit chroma circuit ? color control circuit (bus control) ? tint control circuit (bus control) ? b . p. f. / t. o . f. c i r c u i t ( b us s e le c t ) ? included acc / killer filter sif circuit ? inter carrier sif system ? external sound select switch (bus select) ? attenuator circuit (bus control) text circuit ? linear rgb input ? cut off / drive adjustment (bus adjustment) ? rgb primary color output deflection circuit ? auto-slicer type high performance sync. separation circuit ? adjustment free countdown system ? sync. separation output ? x-ray protect circuit ? ve rt ic al ram p o utp ut ? dual time constant afc circuit ? horizontal and vertical position adjustment (bus adjustment) ? vertical amplitude adjustment (bus adjustment) weight: 5.55g (typ.)
TA1201CNG 2004-05-24 2 block diagram
TA1201CNG 2004-05-24 3 terminal function pin no. pin name function interface circuit 1 2 sound output this terminal is for sound output. the maximum flew out current of these terminals is 3.6ma. so, the minimum load resister is 1k ? . 3 rf agc this terminal is for rf agc output. 4 sif tank coil this terminal is for connecting sif detect tank coil. this terminal is for sound mute switch, too. if this terminal is connected to gnd, the sound output is muted. 5 agc filter this terminal is for pif 2nd agc filter. 6 pif gnd this terminal is for gnd of pif circuit. D 7 8 pif input this terminal is for if input. the typical input value is 90dbv. .
TA1201CNG 2004-05-24 4 pin no. pin name function interface circuit 9 pif v cc this terminal is for v cc of pif circuit. D 10 loop filter this terminal is for pif pll loop filter. 11 apc filter this terminal is for apc filter of f sc oscillation. 12 vcxo this terminal is for x?tal of 3.58mhz vcxo. 13 gnd this terminal is for v / c / d gnd. D 14 fast blanking this terminal is for fast blanking of rgb input.
TA1201CNG 2004-05-24 5 pin no. pin name function interface circuit 15 16 17 analog rgb input these terminals are for rgb signal input. 18 digital v cc this terminal is for v cc of digital circuit. D 19 20 21 rgb output these terminals are for rgb primary color signal output. 22 vertical output this terminal is for vertical pulse output. 23 24 nfb, vertical ramp. these terminals are for nfb input and vertical ramp output.
TA1201CNG 2004-05-24 6 pin no. pin name function interface circuit 25 vertical sync. separation filter this terminal is for vertical sync. separation filter. 26 h. v cc this terminal is for v cc of horizontal circuit. D 27 28 scl, sda these terminals are for input and output of i 2 c bus. 29 x-ray this terminal is for input of x-ray protect circuit. the threshold voltage is 3.5v (typ.). if this terminal is applied the voltage that is more than threshold voltage, the x-ray protect circuit make horizontal output a low. 30 fly-back pulse input this terminal is for fly-back pulse input. the fly-back pulse is the reference of afc circuit, gate pulse and so on. 31 sync. pulse output this terminal is for sync. pulse output. the current needs to keep under 1ma.
TA1201CNG 2004-05-24 7 pin no. pin name function interface circuit 32 horizontal output this terminal is for horizontal pulse output. 33 h. afc this terminal is for horizontal afc filter. the afc circuit fits the phase between inputted horizontal sync. signal and horizontal pulse which is made by countdowning 32f h . 34 32f h vco this terminal is for connecting ceramic oscillator. that constitutes 32f h (503khz) oscillation circuit. the csbla503keczf30 (murata) is recommended. 35 d. gnd this terminal is for gnd of digital circuit. D 36 a.b.l. this terminal is for a.b.l. circuit. 37 tv input this terminal is for input of pif detected signal. the typical input amplitude is 1.0v p-p .
TA1201CNG 2004-05-24 8 pin no. pin name function interface circuit 38 a.c.l. this terminal is for acl circuit. 39 external video input this terminal is for input of external video signal. 40 black peak detection this terminal is for filter of black peak detection. 41 video switch output this terminal is for output of video switch which selects tv signal or external video. amp. gain ; min. 1.7 typ. 1.9, max. 2.1 42 d.c. restoration this terminal is for filter of apl detection.
TA1201CNG 2004-05-24 9 pin no. pin name function interface circuit 43 y input this terminal is for y signal input. the typical input amplitude is 1.0v p-p . 44 a.f.t. this terminal is for aft output. monitor signal output mode can be selected via bus. b 0 b 1 output 0 0 aft 0 1 test purpose only 1 0 b 1 1 rfagc / 2 45 chroma input this terminal is for chrominance signal input. the typical input signal amplitude is 286mv p-p (at burst signal). this ic is to go to test mode with this terminal voltage higher than 4.5v. 46 v / c / d v cc this terminal is for v cc of video, chroma and deflection circuit. D 47 tv detection output this terminal is for pif detected signal output. 48 s.i.f. v cc this terminal is for v cc of sif circuit. D
TA1201CNG 2004-05-24 10 pin no. pin name function interface circuit 49 50 p.i.f. tank coil these terminals are for connecting a tank coil of pif detection circuit. toko corp. products 292gjas-7475bs (45.75mhz), 292gjas-7476bs (58.75mhz) are recommended. 51 s.i.f. gnd this terminal is for gnd of sif circuit. D 52 limiter input this terminal is for input of sif limiter amplifier circuit. 53 tv audio signal input this terminal is for input of sif detected signal. this terminal is connected to pin 54 via capacitor. 54 de-emphasis this terminal is for filter of sif de-emphasis. 55 56 external audio input these terminals are for external audio input.
TA1201CNG 2004-05-24 11 slave address : 88h sub address d7 d6 d5 d4 d3 d2 d1 d0 preset 00 trap color 0000 0000 01 c. filter tint 1100 0000 02 a. sw brightness 0000 0000 03 blk uni-color 0000 0000 04 mute sharpness 0110 0000 05 vertical phase horizontal phase 0001 0000 06 b 0 b 1 audio attenuator 0000 0000 07 b 2 b 3 audio balance 0010 0000 08 b 4 v. sw rf agc 0000 0000 09 afc wpl vertical amplitude 0010 0000 0a v. fixed pif vco 0100 0000 0b r cut off 0000 0000 0c g cut off 0000 0000 0d b cut off 0000 0000 0e g gain 0000 0000 0f b gain 0000 0000 function range (min.~max.) default color ? 60~0db ? 60db tint 42 0 brightness 1.34~2.6~3.86v 1.34v uni-color ? 24~0db ? 24db sharpness ? 18~6db~14db (4mhz gain) 6db audio att ? 85~6db ? 85db audio balance ? 70~0~70db 0db rf agc 65db~105dbv, 000000 : if mute if mute ver. amplitude 1.6~2.4v center pif vco 2.2mhz (35khz / bit) center rgb cut-off ? 0.4~0.4v ? 0.4v gb gain ? 3.1~3.1db ? 3.1db
TA1201CNG 2004-05-24 12 function range (min.~max.) default 3.58 trap (0) : on / (1) : off on chroma filter (0) : band pass filter / (1) : take off filter tof a, v sw (0) : tv mode / (1) : ext. mode tv blk (0) : blk on / (1) : blk off on mute (00) : off / (01) : y mute / (10) : hout stop / (11) : y mute+v stop (01) h. afc (0) : afc12 / (1) : afc1 normal (0) wpl (0) : off / (1) : on off v. fixed mode (0) : normal / (1) : v frequency 60hz fix normal b 0 , b 1 (monitor) pin 44?s output is selectable. (00) : aft voltage / (01) : test mode / (10) : blue output / (11) : half of rf agc voltage aft voltage b 2 , b 3 , b 4 (test mode) bits for test mode. use this ic with these bits (000). (000) read mode d7 d6 d5 d4 d3 d2 d1 d0 por aft if lock aft killer v lock h lock x-ray function contents por (power on reset) (0) : second / (1) : first aft refer to following figure if lock (0) : lock out / (1) : lock in killer (0) : killer on / (1) : killer off v lock (0) : lock in / (1) : lock out det. window : 262h~263h h lock (0) : lock out / (1) : lock in this function is forced to unlock at v p , so data is valid after 50h. x-ray (0) : x-ray off / (1) : x-ray on vertical phase (3bit) this mode is for changing vertical output timing. (vertical picture position is changed 0~7h as right table.) horizontal phase (5bit) this mode is for changing horizontal picture position. horizontal output phase is changed 3s as maximum. aft read bus d 7 d 6 d 5 mode 0 0 0 reference 0 0 1 1h delay 0 1 0 2h delay 0 1 1 3h delay 1 0 0 4h delay 1 0 1 5h delay 1 1 0 6h delay 1 1 1 7h delay
TA1201CNG 2004-05-24 13 i 2 c bus controlled format summary bus controlled format of TA1201CNG is based on i 2 c bus control format of philips. data transfer format s slave address 0 a sub address a data a p 7bit msb 8 bit msb 8bit msb s : start condition p : stop condition a : acknowledge (1) start and stop condition (2) bit transfer (3) acknowledge (4) slave address purchase of toshiba i 2 c components conveys a license under the philips i 2 c patent rights to use these components in an i 2 c system, provided that the system conforms to the i 2 c standard specification as defined by philips. a6 a5 a4 a3 a2 a1 a0 w / r 10001 0 0 0
TA1201CNG 2004-05-24 14 maximum ratings (ta = 25c) characteristic symbol rating unit power supply voltage v cc 12 v power dissipation p d max 2.19 (note1) w input terminal voltage v in gnd ? 0.3~v cc +0.3 v input signal amplitude e in 4 v p-p operating temperature t opr ? 20~65 c storage temperature t stg ? 55~150 c note 1: when using the device at above ta = 25c, decrease the power dissipation by 17.5mw for each increase of 1c. note 2: as this ic is weak in a surge voltage, handle it with care from being damage. recommended operating condition characteristic symbol min typ. max unit remarks pif power supply voltage v ccp 8.5 9.0 9.5 v D sif power supply voltage v ccs 8.5 9.0 9.5 v D v / c / d power supply voltage v ccv 8.5 9.0 9.5 v D h.vcc power supply voltage h.v cc 8.5 9.0 9.5 v D d.vcc power supply voltage d.v cc 2.7 3.3 3.8 v D tv external video input level v in37 / 39 D 1.0 D v p-p including sync. standard video input level v in43 D 1.0 D v p-p including sync. standard chroma input level v in45 D 286 D mv p-p at burst signal fbp width t fbp 10 12 D s v th = 1.4v, v cc ? 1.4v fbp input flow in current i fbpmax D D 2 ma D pif output load resister r op 2 8.2 D k ? D sif output load resister r os 1 8.2 D k ? D rgb output load resister r orgb D 1.8 D k ? D horizontal output load resister r hout 330 800 D ? maximum 10ma vertical output load resister r vout 4.1 5.7 D k ? D sync. separation output flow in current i syncmax D D 1 ma D
TA1201CNG 2004-05-24 15 electrical characteristics dc characteristics (unless otherwise specified, v cc = 9v, h. v cc = 9v, ta = 25c ) pin no. characteristic symbol test cir- cuit test condition min typ. max unit 1 sound output v 1 D D 3.20 3.70 4.20 v 2 sound output v 2 D D 3.20 3.70 4.20 v 3 rf agc v 3 D D D 0.00 0.50 v 4 sif tank v 4 D D D D D v 5 agc filter v 5 D D 7.00 7.50 8.00 v 6 pif gnd gnd D D D 0.00 D v 7 pif input v 7 D D 1.50 2.00 2.50 v 8 pif input v 8 D D D 0.00 0.50 v 9 pif v cc v cc D D D 9.00 D v 10 loop filter v 10 D D D 4.50 D v 11 apc filter v 11 D D 6.00 6.50 7.00 v 12 vcxo v 12 D D 5.30 5.80 6.30 v 13 v / c / d gnd gnd D D D 0.00 D v 14 f-blk v 14 D D D 0.00 D v 15 analog r input v 15 D D 4.40 4.90 5.40 v 16 analog g input v 16 D 4.40 4.90 5.40 v 17 analog b input v 17 D D 4.40 4.90 5.40 v 18 d. v cc v cc D D D 3.30 D v 19 r output v 19 D brt, c. o cent 2.40 2.70 2.90 v 20 g output v 20 D brt, c. o cent 2.40 2.70 2.90 v 21 b output v 21 D brt, c. o cent 2.40 2.70 2.90 v 22 v out v 22 D D D D D 23 nfb v 23 D D D D D D 24 v. ramp v 24 D D D D D 25 v sepa v 25 D D 5.80 6.30 6.80 v 26 h. v cc v 26 D D D 9.00 D v 27 scl v 27 D D 4.50 5.00 5.50 v 28 sda v 28 D D 4.50 5.00 5.50 v 29 x-ray v 29 D D D 0.00 D v 30 fbp input v 30 D D D D D D 31 sync. output v 31 D D D D D D 32 h. output v 32 D D D D D D 33 h. afc v 33 D D 7.00 7.50 8.00 v 34 32f h vco v 34 D D 5.50 6.00 6.50 v 35 d. gnd gnd D D D 0.00 D v 36 abl v 36 D brt, col cent 2.90 3.40 3.90 v 37 tv input v 37 D D 2.90 3.00 3.90 v 38 acl v 38 D brt, col cent 2.90 3.40 3.90 v
TA1201CNG 2004-05-24 16 pin no. characteristic symbol test cir- cuit test condition min typ. max unit 39 ext. video input v 39 D D 1.10 1.60 2.10 v 40 black det v 40 D D 6.10 6.60 7.10 v 41 av / sw output v 41 D D 1.80 2.30 2.80 v 42 dc rest v 42 D D 5.50 6.00 6.50 v 43 y input v 43 D D 4.00 4.50 5.00 v 44 aft v 44 D D 2.00 2.50 3.00 v 45 chroma input v 45 D D 1.60 1.85 2.10 v 46 v / c / d v cc v 46 D D D 9.00 D v 47 tv det. output v 47 D D 4.70 5.20 5.70 v 48 sif v cc v cc D D D 9.00 D v 49 pif tank v 49 D D D D D v 50 pif tank v 50 D D D D D v 51 sif gnd v cc D D D 0.00 D v 52 limiter input v 52 D D D 0.00 0.50 v 53 audio tv input v 53 D D 2.50 3.00 3.50 v 54 de-emphasis v 54 D pin4 gnd 4.00 4.50 5.00 v 55 ext. audio input v 55 D D 2.50 3.00 3.50 v 56 ext. audio input v 56 D D 2.50 3.00 3.50 v current consumption characteristic symbol test condition min typ. max unit if power supply current i cci D 32.8 46 52.0 ma v / c / d power supply current i ccv D 52.7 71 76.8 ma h. v cc power supply current i cch D 10.7 14 18.4 ma d. v cc power supply current i ccd D 5.2 10 11.6 ma
TA1201CNG 2004-05-24 17 ac characteristics (unless otherwise specified, v cc = 9v, h. v cc = 9v, ta = 25c) pif characteristic symbol test cir- cuit test condition min typ. max unit v 01 1.7 2.0 2.3 video detected output level v 02 D (note 1) 2.0 2.5 3.0 v p-p v in min D 42 D input sensitivity v in max D (note 2) 100 107 D dbv sync tip level v sync D (note 3) 2.6 2.9 3.2 v output level for no input v if D (note 4) 4.8 5.2 5.6 v differential gain dg D 2 5 % differential phase dp D (note 5) D 2 5 pif output frequency characteristic f c D (note 6) 5 7 D mhz carrier wave compression ratio cr 50 55 D 2nd harmonics compression ratio hr D (note 7) 50 55 D db pif input resistance r ipif D 1.5 D k ? pif input capacitance c ipif D (note 8) D 3.8 D pf s / n s / n D (note 9) 52 55 D db 920khz beat i 920 D (note 10) 42 45 D db if agc range rw agc D (note 11) 61 65 69 db v 5mean 4.2 4.5 4.8 v 5max 7.4 7.6 D if agc voltage v 5min D (note 12) D 3.8 D v v 3max 7.7 8.2 D rf agc voltage v 3min D (note 13) D 0 0.5 v rf agc control range ? g rfagc D (note 14) 35 40 D db aft center voltage v 4cent D (note 15) 2.2 2.5 2.8 v v 4max 4.4 4.8 D aft voltage v 4min D (note 16) D 0.2 0.5 v aft sensitivity aft D (note 17) D 40 D khz / v aft output resistance r aftout D (note 18) 40 50 60 k ? pif vco control sensitivity ifvco D (note 19) 2.0 2.5 D mhz / v f ph 1.0 1.5 D pif vco pull-in range f pl D (note 20) 1.0 1.5 D mhz pif vco control range ? f pifvco D (note 21) D 4.4 D mhz
TA1201CNG 2004-05-24 18 sif characteristic symbol test cir- cuit test condition min typ. max unit v aac 400 500 600 mv rms sound output level v adc D (note 22) D 4.5 D v sound distortion v audio D (note 23) D 0.3 1.0 % amr amr D (note 24) 50 60 D db limiting sensitivity v lim D (note 25) D 35 D dbv f audioh D 130 D sound output frequency characteristics f audiol D (note 26) D ? 130 D khz sound output resistance r sout D (note 27) 24 30 36 k ? at t characteristic symbol test cir- cuit test condition min typ. max unit g attmaxe ? 2.0 0.0 2.0 g attmaxt 4.0 6.0 8.0 g attmean ? 16 ? 12 ? 9 att gain g attmin D (note 28) ? 99 ? 85 D db v 1var D D 50 mv dc voltage drift v 1dc D (note 29) 3.2 3.7 4.2 v r i53 D 30 D input impedance r i55 D (note 30) D 47 D k ? b max 45 58 70 balance characteristics b min D (note 31) ? 70 ? 58 ? 45 db video characteristic symbol test cir- cuit test condition min typ. max unit input impedance r i41 D (note 32) 100 D D k ? input dynamic range v di41 D (note 33) 1.0 1.2 1.5 v video total gain g y D (note 34) 4.5 5.0 D video frequency characteristic f y D (note 35) 6.0 7.0 D mhz maximum output v do1 D (note 36) 7.5 8.0 D v black expansion amp. gain g bamp 1.18 1.43 1.68 black expansion start point g bstp D (note 37) 40 50 60 ire dc restoration t dc D (note 38) 100 103 105 % g shcent 1 4 7 g shmax 9 12 15 sharpness control characteristics g shmin D (note 39) D ? 18 ? 15 db sharpness delay time t shdly D (note 40) D 125 D ns g cncent D 4.5 6 7.5 contrast control characteristics g cnmin D (note 41) 22.5 24 28.5 db h. v-blk output voltage v blk D (note 42) D 0.7 1.0 v v-blk width t vblk D (note 43) D 3.5~24 D h f sc trap gain g trap D (note 44) D ? 28 ? 20 db
TA1201CNG 2004-05-24 19 osd characteristic symbol test cir- cuit test condition min typ. max unit osd switching voltage v thosd D (note 45) 0.7 1.0 1.3 v osd delay time t osddly D 15 30 osd delay time difference t osdd D 5 10 osd rising time r D 15 30 osd falling time f D (note 46) D 15 30 ns input clamp voltage v osdc D (note 47) 4.4 4.9 5.4 v osd gain g osd D (note 48) 1.8 2.0 2.2 input dynamic range v diosd (note 49) 2.0 2.2 2.4 v cutoff drive characteristic symbol test cir- cuit test condition min typ. max unit v brtmax 3.6 4.0 4.3 v brtcen 2.4 2.7 3.0 brightness control characteristics v brtmin D (note 50) 1.0 1.4 1.7 v brightness control difference between 3axes ? vrgb D (note 51) ? 50 0 50 mv v cutmax 0.5 0.65 0.8 v cutcen D 0.00 D cutoff control characteristics v cutmin D (note 52) ? 0.8 ? 0.65 ? 0.5 v g drvmax 3.75 4.25 4.75 drive control characteristics g drvmin D (note 53) ? 4.0 ? 3.5 ? 3.0 db chroma characteristic symbol test cir- cuit test condition min typ. max unit input dynamic range v di45 D (note 54) 0.95 1.5 1.7 v ea ? 23 ? 20 ? 17 eb 3 6 9 db acc characteristic a D (note 55) 0.9 1.0 1.1 D killer point ek D (note 56) ? 48 ? 46 ? 43 db vcxo frequency control range ? f vcxo D (note 57) 500 600 D hz vcxo frequency control sensitivity vcxo D (note 58) D 1.0 D hz / mv vcxo pull-in range f vcxopl D (note 59) 300 450 D hz r / b 0.78 0.83 0.88 demodulate relative gain g / b 0.31 0.35 0.39 D r-b 84 91 98 demodulate relative phase g-b D (note 60) 233 240 247 e cr D 20 40 e cb D 20 40 carrier wave remain e cg D (note 61) D 20 40 mv p-p
TA1201CNG 2004-05-24 20 characteristic symbol test cir- cuit test condition min typ. max unit v clrmax 3.9 4.1 4.3 v p-p g clrcen 4.5 6 7.5 color control characteristic g clrmin D (note 62) 38 40 D db g unicen 4.5 6 7.5 uni-color control characteristic g unimin D (note 63) 22 24 26 db tntcen ? 7 0 7 tint control characteristic ? tnt D (note 64) 35 45 55 video chroma delay time t v-c D (note 65) ? 30 0 30 ns deflection characteristic symbol test cir- cuit test condition min typ. max unit horizontal free run freq. f h D (note 66) ? 100 0 100 hz h. out pulse duty t h D (note 67) 38 41 44 % v hl D 0.2 0.3 h. out voltage v hh D (note 68) 2.5 3.0 3.5 v vco osc. start voltage v oscmin D (note 69) 3.0 3.5 4.0 v h. out start voltage v hst D (note 70) 3.7 4.0 D v h. frequency control range ? f h D (note 71) 500 650 D hz h. freq. control sensitivity h D (note 72) D 500 D hz / v h. sync. pull-in range ? f hpul D (note 73) 450 500 D hz h. pull-in stop period t hstp D (note 74) D 259 ~272 D h afc-2 control range t afc2 D (note 75) 16 17 D s horizontal position adjustment t pafc2 D (note 76) D 3 D s x-ray protection detection voltage v xdet 3.35 3.5 3.65 x-ray protection hold voltage v xhld 3.9 4.2 4.5 v x-ray protection hold current v xld D (note 77) 80 100 120 a vertical free run freq. f v D (note 78) D 295 D h t vst D 224 D v. sync. pull-in range t vend D (note 79) D 295 D h v. out pulse width t v D (note 80) D 8 D h v vl 2.2 2.4 D v. ramp amplitude control v vh D (note 81) D 1.6 1.8 v h. sync. separation level r sepa D (note 82) 30 35 40 % forced v. osc. (262.5h) f v60 D (note 83) D 60 D hz
TA1201CNG 2004-05-24 21 test condition test condition (v cc = 9v, ta = 253c) bus mode note item (06) (07) (08) (0a) measurement method 1 video detected output level (00) (20) (20) D (1) apply the if signal. (f 0 = 45.75mhz, 87.5% am, 31.6mv rms ) to if input. (2) measure the output signal level at pin 47. (v 01 ) (3) apply the signal (100% am, 31.6mv rms ) to if input. (4) measure the output signal level pin 47. (v 02 ) 2 input sensitivity (1) apply the signal (f 0 = 45.75mhz, 30% am, 31.6mv rms ) to if input. (2) decrease input signal level. measure the input signal level at if input, when output signal level at pin 47 decreases as ? 3db level. (v in min ) (3) increase input signal level. measure the input signal level at if input, when output signal level at pin 47 increases as +0.5db level. (v in max ) 3 sync. tip level (1) apply the signal (f 0 = 45.75mhz, 31.6mv rms , non modulation) to if input. (2) measure the dc voltage at pin 47 (v sync ) 4 output level for no input (1) non if input (2) apply 3.0v at pin 5. (3) measure the dc voltage at pin 47. (v if ) 5 differencial gain differencial phase (1) apply the if signal (f 0 = 45.75mhz, 87.5% am video) to if input. (2) measure the differencial gain and phase at pin 47.
TA1201CNG 2004-05-24 22 test condition (v cc = 9v, ta = 253c) bus mode note item (06) (07) (08) (0a) measurement method 6 pif output frequency characteristics (00) (20) (20) D (1) same as note 3 (1) (2) fix the voltage at pin 5. (3) apply the signal as follows to if input, f 0 = 45.75mhz 31.6mv rms f 1 = 45.65~32mhz 3.16mv rms (4) measure f 1 frequency, when the output level at pin 47 becomes ? 3db. f c = f 0 ? f 1 7 carrier wave compression ratio 2nd harmonics compression ratio (1) apply the signal (f 0 = 45.75mhz, f m = 15.75khz, 78% am, 31.6mv rms ) to if input. (2) apply the voltage at pin 5 so that output level of pin 47 becomes 2v p-p. (3) measure the leak level of carrier wave at pin 47 when non modulation if signal is input. cr = 20 ? og (2 (v p-p ) / the leak level of carrier wave (mv rms ) ) (4) measure the leak level of 2nd harmonics in the same way. hr = 20 ? og (2 (v p-p ) / the leak level of 2nd harmonics (mv rms ) ) 8 pif input resistance pif input capacitance (1) apply 3.0v to pin 5. (2) measure the impedance between pin 7 and 8. 9 s / n (1) same as note 2 (1) (2) measure output level at pin 47 (va) (3) same as note 3 (1) (4) measure output level at pin 47 (vb) s / n = 20 ? og (va / vb6)
TA1201CNG 2004-05-24 23 test condition (v cc = 9v, ta = 253c) bus mode note item (06) (07) (08) (0a) measurement method 10 920khz beat (00) (20) (20) D (1) apply the signals as follows to if input, f 0 = 45.75mhz 31.6mv rms f c = 42.17mhz 10.0mv rms f s = 41.25mhz 10.0mv rms (2) apply the voltage so that the lowest of the output at pin 47 is equal v sync . (3) measure the difference between f c and 920khz beat. 11 if agc range rw agc = v inmax ? v inmin 12 if agc voltage (1) same as note 3 (1) (2) measure the voltage at pin 5. (v 5mean ) (3) measure the voltage at pin 5 when no input. (v 5max ) (4) measure the voltage at pin 5 when input signal level is 178mv rms (v 5min ). 13 rf agc voltage ad- just (1) same as note 3 (1) (2) adjust the data of sub-address (08) (rf agc) so that the voltage at pin 3 become 4.5v. (3) measure the voltage at pin 3 when no input. (v 3max ) (4) measure the voltage at pin 3 when input signal level is 178mv rms (v3 min ).
TA1201CNG 2004-05-24 24 test condition (v cc = 9v, ta = 253c) bus mode note item (06) (07) (08) (0a) measurement method 14 rf agc control range (00) (20) ad- just D (1) same as note 3 (1) (2) set the data of sub-address (08) to (00). decrease the if input level. measure the if input level, when the voltage of pin 3 become 4.5v. (v rfmin ) (3) set the data of sub-address (08) to (3f). measure the if input level, when the voltage of pin 3 become 4.5v. (v rfmax ) ? v rfagc = v rfmin ? v rfmax 15 aft center voltage (20) (1) no if input (2) apply 3.0v to pin 5. (3) measure the voltage at pin 44. (v 4cent ) 16 aft voltage (1) apply the signal (f = 44.75mhz, 30% am video, 31.6mv rms ) to if input. (2) measure the output signal level at pin 44. (v 4max ) (3) apply the signal (f = 46.75mhz, 30% am video, 31.6mv rms ) to if input. (4) measure the output signal level at pin 4. (v 4min ) 17 aft sensitivity (1) same as note 3 (1) (2) measure the voltage change at pin 44 when input frequency is changed. ( ? f / ? v ) 18 aft output resistance measure the output impedance of pin 44.
TA1201CNG 2004-05-24 25 test condition (v cc = 9v, ta = 253c) bus mode note item (06) (07) (08) (0a) measurement method 19 pif vco control sensitivity (00) (20) (20) D (1) apply the signal (f = 45.75mhz, 31.6mv rms , cw) to if input. (2) measure the dc voltage at pin 10. (v10a) (3) apply the signal (f = 45.55mhz, 31.6mv rms , cw) to if input. (4) measure the dc voltage at pin 10. (v10b) ifvco = 0.2 (mhz) / (v10b ? v10a) (v) [mhz / v] 20 pif vco pull-in range (1) apply the signal (f = 45.75mhz, 31.6mv rms , cw) to if input. (2) observe output signal at pin 47 and change the if input frequency from higher to lower. measure the if input frequency when pll is locked. calculate the frequency difference between above frequency and 45.75mhz. (fph) (3) observe output signal at pin 47 and change the if input frequency from lower to higher. measure the if input frequency when pll is locked. calculate the frequency difference between above frequency and 45.75mhz. (fpl) 21 pif vco control range ad- just (1) no if input. (2) apply 3.0v to pin 5. (3) measure the frequency of pif vco when the data of sub-address (0a) is set (00) (f pifmin ) (4) measure the frequency of pif vco when the data of sub-address (0a) is set (7f) (f pifmax )
TA1201CNG 2004-05-24 26 test condition (v cc = 9v, ta = 253c) bus mode note item (06) (07) (08) (0a) sw 52 measurement method 22 sound output level (00) (20) (20) D on (1) apply the signal (f 0 = 4.5mhz, f m = 400hz, 25khz / devi fm, 100mv rms ) to pin 52. (2) measure the output signal amplitude pin 54. 23 sound distortion (1) same as note 22 (1) (2) measure the distortion of output signal at pin 54. 24 amr (1) apply the signals as follows to pin 52, fm : 400hz 25khz / devi fm, 100mv rms am : 400hz 30% 100mv rms (2) measure the output level at pin 54 against each input. amr = 20 ? og (fm / am) 25 limiting sensitivity (1) same as note 22 (1) (2) change the input level. measure the input level when the output level at pin 54 become ? 3db. 26 sound output frequency characteristics (1) same as note 22 (1) (2) change the input frequency. measure the input frequency when the output level at pin 54 become ? 3db compare with peak level. 27 sound output resistance off measure the output impedance at pin 54.
TA1201CNG 2004-05-24 27 test condition (v cc = 9v, ta = 253c) bus mode note item (02) (06) (07) (08) (0a) measurement method 28 att gain (80) ad- just (20) (20) D (1) apply the signal (1khz, 500mv rms ) to pin 55 and 56. (2) set the data of sub-address (02) to (80) (3) measure the output level at pin 1 and 2 when the data of sub-address (06) is set to (3f) (v attmax ) g attmax = 20 ? og (v attmax / 500mv rms ) (4) measure the output level at pin 1 and 2 when the data of sub-address (06) is set to (20) (v attmax ) g attmean = 20 ? og (v attmean / v attmax ) (5) measure the output level at pin 1 and 2 when the data of sub-address (06) is set to (00) (v attmin ) g attmin = 20 ? og (v attmin / v attmax ) 29 dc voltage drift (1) same as note 28 (1) (2) same as note 28 (2) (3) measure the dc voltage at pin 1 and 2. (v 2dc ) (4) measure the voltage change at pin 1 and 2 when the data of sub-address (06) is changed from (20) to (00). (v 2var ) 30 input impedance (20) measure the input impedance of pin 53, 55 and 56. 31 balance characteristics ad- just (1) same as note 28 (1) (2) same as note 28 (2) (3) measure the output level difference between pin 1 and 2 when the data of sub-address (07) is set to (00) and (3f).
TA1201CNG 2004-05-24 28 test condition (v cc = 9v, ta = 253c) bus mode note item (00) (02) (03) (04) (0b) (0c) (0d) measurement method 32 input impedance (00) (00) (40) (20) (80) (80) (80) measure the input impedance of pin 37 and 39. 33 input dynamic range (1) tv mode : change the voltage in picture period at pin 37. external mode : change the voltage in picture period at pin 39. (2) consider the change of r output as 100%. measure the dc voltage at pin 19 when output level of pin 19 is 10% (v di1 ). measure the dc voltage at pin 41 when output level of pin 19 is 90% (v di2 ). v di41 = v di2 ? v di1 34 video total gain (7f) (1) tv mode : apply the input signal 1 (f 0 = 10khz, 0.5v p-p ) external mode : apply the input signal 1 (f 0 = 10khz, 0.5v p-p ) (2) measure the sine wave signal amplitude at pin 19 (v 9 ) g-y = 20 ? og (v 9 / 0.5v p-p ) 35 video frequency characteristics (40) measure input frequency when the output level becomes ? 3db. 36 maximum output (7f) (1) same as note 33 (1) (2) measure the maximum output level at pin 19.
TA1201CNG 2004-05-24 29 test condition (v cc = 9v, ta = 253c) bus mode note item (00) (02) (03) (04) (0b) (0c) (0d) measurement method 37 black expansion amp. gain black expansion start point (00) (00) (40) (20) (80) (80) (80) (1) apply 1v p-p video signal as follows to video input. (2) measure the start point and amp gain of black expansion at pin 19. 38 dc restoration ad- just (1) tv mode : apply input signal 1 (f 0 = 10khz 0.5v p-p ) to pin 37. external mode : apply input signal 1 (f 0 = 10khz 0.5v p-p ) to pin 39. (2) make pin 42 open. adjust the data of sub-address (03) so that the output signal amplitude at pin 21 become 0.5v p-p . (3) measure the pedestal level at pin 21 when no luminance signal is input. ( ? y ) tcd = ( ? y / 0.5v)100% [%] 39 sharpness control characteristics (40) ad- just (1) apply input signal 1 (20mv p-p ) to pin 39. (2) set the data of sub-address (04) is (3f) (3) measure the output signal amplitude at b out when the signal (f 0 = 10khz) is applied (v 10k ) and when the signal (f 0 = 4mhz) is applied (v pk ). g shmax = 20 ? og (v pk / v 10k ) (4) set the data of sub-address (04) is (00) (5) measure the output signal amplitude (v pk ) at b output when the signal (f 0 = 2.4mhz) is applied. g shmin = 20 ? og (v pk / v 10k ) (6) set the data of sub-address (04) is (20) (7) measure the output signal amplitude (v pk ) at b output when the signal (f 0 = 4.0mhz) is applied. g shcent = 20 ? og (v pk / v 10k )
TA1201CNG 2004-05-24 30 test condition (v cc = 9v, ta = 253c) bus mode note item (00) (02) (03) (04) (0b) (0c) (0d) measurement method 40 sharpness delay time (00) (00) (40) (3f) (80) (80) (80) measure width of sharpness pulse. 41 contrast control characteristic ad- just (20) (1) apply input signal 1 (f 0 = 10khz, 0.5v p-p ) to pin 39. (2) set the data of sub-address (03) is (40). (3) measure the output signal amplitude at pin 21. (v cncent ) (4) measure the output signal amplitude at pin 21 when the data of sub-address (03) is set (7f) (v cnmax ) (5) measure the output signal amplitude at pin 21 when the data of sub-address (03) is set (00) (v cnmin ) g cnmax = 20 ? og (v cnmax / v cncent ) g cnmin = 20 ? og (v cnmin / v cnmax ) 42 h.v-blanking output voltage (40) measure the blanking pulse voltage at pin 21. 43 v-blanking width measure the blanking pulse width at pin 21. 44 f sc trap gain (80) (00) (1) apply input signal 2. (f 0 = 3.58mhz, 0.5v p-p ) to pin 39. (2) measure the output signal amplitude at b out when the data of sub-address (00) is set (80). (v ton ) (3) measure the output signal amplitude at b out when the data of sub-address (00) is set (00). (v toff )
TA1201CNG 2004-05-24 31 test condition (v cc = 9v, ta = 253c) bus mode note item (00) (02) (03) (04) (0b) (0c) (0d) measurement method 45 osd switching voltage (00) (00) (40) (20) (80) (80) (80) (1) apply the external voltage to pin 14. increase the external voltage from 0v. (2) measure the voltage at pin 14 when the voltage of pin 19, 20 and 21 at picture period are changed. 46 osd delay time osd delay time difference among 3 axis osd rising time osd falling time (1) apply 1.5v to pin 14. (2) apply the signal as following fig. (a) to pin 15. (3) measure t r and t f of r output at pin 19 according fig. (b) (4) measure about g and b axis in the same way. 47 input clamp voltage (1) apply 1.5v to pin 14. (2) measure the voltage at pin 15, 16 and 17.
TA1201CNG 2004-05-24 32 test condition (v cc = 9v, ta = 253c) bus mode note item (00) (02) (03) (04) (0b) (0c) (0d) measurement method 48 osd gain (00) (00) (40) (20) (80) (80) (80) (1) apply 1.5v to pin 14. (2) apply the sine wave signal (10khz, 0.5v p-p ) to pin 15, 16 and 17. (3) measure the output signal of pin 19, 20 and 21. (v 41 ) g-osd = (v 41 / 0.5v p-p ) 49 input dynamic range (1) apply 1 .5v to pin 14. (2) apply the sine wave signal (10khz) to pin 15, 16 and 17 with variable amplitude. (3) consider the output change as 100%. measure the input signal level when the output signal level is 10%, (v di1 ) and when the output signal level is 90%. (v di2 ) v diosd = v di2 ? v di1
TA1201CNG 2004-05-24 33 test condition (v cc = 9v, ta = 253c) bus mode note item (00) (02) (03) (04) (0b) (0c) (0d) (0f) measurement method 50 brightness control characteristics (00) ad- just (40) (80) (80) (80) (00) (00) (1) apply a color bar signal to pin 39. (2) measure the pedestal level of rgb output signal at pin 19, 20 and 21 when the data of sub-address (02) is set (7f). (v brtmax ) (3) measure the pedestal level of rgb output signal at pin 19, 20 and 21 when the data of sub-address (02) is set (40). (v brtcest ) (4) measure the pedestal level of rgb output signal at pin 19, 20 and 21 when the data of sub-address (02) is set (00). (v brtmin ) 51 brightness control difference between 3 axis. (40) (1) apply a color bar signal to pin 39. (2) measure the difference of pedestal voltage among 3 axis at pin 19, 20 and 21. 52 cut off characteristics ad- just ad- just ad- just (1) apply a color bar signal to pin 39. (2) measure the pedestal level of rgb output signal at pin 19, 20 and 21 when the data of sub-address (0b, 0c, 0d) is set (ff) (v cutmax? ) v cutmax = v cutmax? ? v brtcen (3) measure the pedestal level of rgb output signal at pin 19, 20 and 21 when the data of sub-address (0b, 0c, 0d) is set (80) (v cutcen? ) v cutcen = v cutcen? ? v brtcen (4) measure the pedestal level of rgb output signal at pin 19, 20 and 21 when the data of sub-address (0b, 0c, 0d) is set (00) (v cutmin? ) v cutmin = v cutmin? ? v brtcen
TA1201CNG 2004-05-24 34 test condition (v cc = 9v, ta = 253c) bus mode note item (00) (02) (03) (04) (0b) (0c) (0d) (0f) measurement method 53 drive control characteristics (40) (00) (40) (80) (80) (80) ad- just ad- just (1) apply the input signal 1 (f 0 = 10khz, 0.5v p-p ) to pin 39. (2) measure the voltage of g and b output signal at picture period at pin 20 and 21 when the data of sub-address (0e, 0f) is set (80) (v drvcen ) (3) measure the voltage of g and b output signal at picture period at pin 20 and 21 when the data of sub-address (0e, 0f) is set (ff) (v drvmax ) g drvmax = 20 ? og (v drvmax / v drvcen ) (4) measure the voltage of g and b output signal at picture period at pin 20 and 21 when the data of sub-address (0e, 0f) is set (00) (v drvmin ) g drvmin = 20 ? og (v drvmin / v drvcen )
TA1201CNG 2004-05-24 35 test condition (v cc = 9v, ta = 253c) bus mode note item (00) (01) (02) (03) (0e) (0f) measurement method 54 input dynamic range (40) (40) (00) (40) (80) (80) (1) change the voltage of external input signal at picture period at pin 39. (2) consider the output change at pin 21 as 100%. measure the output signal amplitude at pin 21 when the output signal is 10% (v di1 ) and when the output signal is 90% (v di2 ). v di45 = v di2 ? v di1 55 acc characteristic (1) apply a rainbow color bar signal to pin 39. (2) measure the rgb output signal as f 1 and f 3 at pin 19, 20 and 21 when the input signal level is 100mv p-p and 300mv p-p. a = f 1 / f 3 56 killer point apply the burst signal (50mv p-p ) to pin 39. decrease the input level by using att. measure the input burst signal when color killer on. 57 vcxo frequency control range (1) measure the dc voltage at pin 11. (v 11 ) (2) measure the frequency change at pin 12 when the voltage of pin 11 is change from v 11 ? 0.5v to v 11 +0.5v. 58 vcxo frequency control sensitivity (1) same as note 57 (1) (2) same as note 57 (2) (3) measure the sensitivity against 1mv at pin 11.
TA1201CNG 2004-05-24 36 test condition (v cc = 9v, ta = 253c) bus mode note item (00) (01) (02) (03) (0e) (0f) measurement method 59 vcxo pull-in range (40) (40) (00) (40) (80) (80) (1) apply a rainbow color bar signal to pin 39. (2) observe the rgb output signal at pin 19, 20 and 21. change input f sc frequency by 10hz step up to 3khz. measure the pull-in range. 60 demodulate relative gain demodulate relative phase (1) apply the rainbow color bar signal (f sc = 3.579545mhz, 0.3v p-p ) to pin 39. (2) measure the amplitude and phase at pin 19, 20 and 21. calculate r / b, g / b, r-b, g-b. 61 carrier wave remain ad- just (1) apply a rainbow color bar signal to pin 39. (2) adjust the data of sub-address (01) so that the rgb output amplitude at pin 19, 20 and 21 will be maximum. (3) apply the signal that has only sync. and burst signal to pin 39. (4) measure the f sc components of rgb output signal at pin 19, 20 and 21. 62 color control characteristic a d- just (40) (1) apply a rainbow color bar signal to pin 39. (2) measure the amplitude of rgb output signal at pin 19, 20 and 21 when the data of sub-address (00) is set (7f). (v clrmax ) (3) measure the amplitude of rgb output signal at pin 19, 20 and 21 when the data of sub-address (00) is set (40). (v clrcen ) g clrcen = 20 ? og (v clrmax / c clrcen ) (4) measure the amplitude of rgb output signal at pin 19, 20 and 21 when the data of sub-address (00) is set (00). (v clrmin ) g clrmin = 20 ? og (v clrmax / v clrmin )
TA1201CNG 2004-05-24 37 test condition (v cc = 9v, ta = 253c) bus mode note item (00) (01) (02) (03) (0e) (0f) measurement method 63 uni-color control characteristic (40) (40) (00) ad- just (80) (80) (1) apply a rainbow color bar signal to pin 39. (2) measure the amplitude of rgb output signal at pin 19, 20 and 21 when the data of sub-address (03) is set (7f). (v unimax ) (3) measure the amplitude of rgb output signal at pin 19, 20 and 21 when the data of sub-address (03) is set (40). (v unicen ) g unicen = 20 ? og (v unimax / v unicen ) (4) measure the amplitude of rgb output signal at pin 19, 20 and 21 when the data of sub-address (03) is set (00). (v unimin ) g unimin = 20 ? og (v unimax / v unimin ) 64 tint control characteristic ad- just (40) (1) apply a rainbow color bar signal to pin 39. (2) adjust the data of sub-address (01) so that the 6th bar of b output signal at pin 21. ( tntcen ) (3) measure phase change of b output signal at pin 21 when the data of sub-address (01) is change from (00) to (7f). ( ? tnt ) 65 video chroma delay time (40) (00) (40) (1) apply a rainbow color bar signal to pin 39. (2) measure rising time of color signal at pin 19, 20 and 21. when the data of sub-address (04) is set (60). (dtc) (3) measure rising time of y signal at pin 19, 20 and 21 when the data of sub-address (04) is set (00). (dty) t v-c = dty ? dtc
TA1201CNG 2004-05-24 38 test condition (v cc = 9v, ta = 253c) bus mode note item (05) (09) (0a) measurement method 66 horizontal free run frequency (10) (20) (40) measure the frequency of h-out at pin 32. (f h? ) f h = f h? ? 15.734khz 67 horizontal out pulse duty measure the duty of horizontal pulse at pin 32. 68 horizontal out voltage measure the high level and low level at pin 32. 69 vco oscillation start voltage increase h. v cc from 0v at pin 26. measure the h. v cc at pin 26 when vco starts oscillation. 70 horizontal output start voltage increase h. v cc from 0v at pin 26.measure the h. v cc at pin 26 when horizontal pulse starts to output at pin 32. 71 horizontal frequency control range (1) measure the dc voltage at pin 33. (2) measure horizontal frequency control range when the voltage of pin 33 is changed from v 33 ? 0.5v to v 33 +0.5v. 72 horizontal frequency control sensitivity (1) same as note 71 (1) (2) same as note 71 (2) (3) measure horizontal frequency control sensitivity against 1mv at pin 33.
TA1201CNG 2004-05-24 39 test condition (v cc = 9v, ta = 253c) bus mode note item (05) (09) (0a) sw 30 measurement method 73 horizontal sync. pull-in range (10) (20) (40) off (1) apply sync. signal to pin 39. (2) observe horizontal output at pin 32. change the input sync. frequency by 10hz step up to 3khz. measure the pull-in range. 74 horizontal sync. pull-in stop period (1) apply sync. signal to pin 39. (2) observe input sync. signal and pin 33. measure the pull-in stop period as follows. 75 afc-2 control range on off (1) sw 30 is on, and delay the rising of fbp from rising of horizontal out by 1s step. (2) sw 30 is off. measure the maximum delay time which afc2 can pull-in. 76 horizontal sync. position adjustment off (1) measure the phase of horizontal out when the data of sub-address (05) is set (10). (2) measure phase change when the data of sub-address (05) is change to (00) and (1f).
TA1201CNG 2004-05-24 40 test condition (v cc = 9v, ta = 253c) bus mode note item (05) (09) (0a) measurement method 77 x-ray protection detect voltage x-ray protection hold voltage x-ray protection hold current (10) (20) (40) (1) connect external voltage supply to pin 29. (2) measure each point as follows. i xld = (v 29off ? v xoff ) / 10k ? 78 vertical free run frequency measure vertical frequency at pin 22. (f v? ) f v = f v? / 15.734khz 79 vertical sync. pull-in range (1) apply sync. signal to pin 39. (2) observe vertical output at pin 22. change input frequency by 0.5h step. measure vertical sync. pull-in range. 80 vertical pulse width measure vertical pulse width as follows.
TA1201CNG 2004-05-24 41 test condition (v cc = 9v, ta = 253c) bus mode note item (05) (09) (0a) measurement method 81 vertical ramp amplitude control (10) ad- just (40) (1) measure vertical ramp amplitude when the data of sub-address (09) is set (3f). (v vh ) (2) measure vertical ramp amplitude when the data of sub-address (09) is set (00). (v vl ) 82 horizontal sync. separation level (20) (1) apply white 100% signal that has short sync. every 10h to pin 39. (2) observe sync. separation output at pin 31. measure sync. separation level by changing sync. length. 83 forced v. osc. (262.5h) (c0) (1) set the data of sub-address (0a) to (c0). (2) measure vertical frequency at pin 22.
TA1201CNG 2004-05-24 42 test circuit t a 1 2 0 1 c n g
TA1201CNG 2004-05-24 43 signal for measurement 1) input signal 1 2) input signal 2
TA1201CNG 2004-05-24 44 application circuit t a 1 2 0 1 c n g
TA1201CNG 2004-05-24 45 package dimensions sdip56-p-600-1.78 unit: mm weight: 5.55g (typ.)
TA1201CNG 2004-05-24 46 ? the information contained herein is subject to change without notice. ? the information contained herein is presented only as a guide for the applications of our products. no responsibility is assumed by toshiba for any infringements of patents or other rights of the third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of toshiba or others. ? toshiba is continually working to improve the quality an d reliability of its products. nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. it is the responsibility of the buyer, when utilizing toshiba products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such toshiba products could cause loss of human life, bodily injury or damage to property. in developing your designs, please ensure that toshiba products are used within specified operating ranges as set forth in the most recent toshiba products specifications. also, please keep in mind the precautions and conditions set forth in the ?handling guide for semiconductor devices,? or ?toshiba semiconductor reliability handbook? etc.. ? the toshiba products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). these toshiba products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfuncti on or failure of which may cause loss of human life or bodily injury (?unintended usage?). unintended usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. unintended usage of toshiba products listed in this document shall be made at the customer?s own risk. ? the products described in this document are subject to the foreign exchange and foreign trade laws. ? toshiba products should not be embedded to the downstream products which are prohibited to be produced and sold, under any law and regulations. 030619eba restrictions on product use about solderabilit y, following conditions were confirmed ? solderability (1) use of sn-63pb solder bath solder bath temperature = 230c dipping time = 5 seconds the number of times = once use of r-type flux (2) use of sn-3.0ag-0.5cu solder bath solder bath temperature = 245c dipping time = 5 seconds the number of times = once use of r-type flux

▲Up To Search▲

Price & Availability of TA1201CNG

	To Download TA1201CNG Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .